Multi-Touch Attribution & Marketing Mix Modeling (MMM)Playbook3 min readUpdated September 2026

Set a Sales and Marketing SLA You Can Actually Measure

A sales and marketing SLA, an agreed standard for how fast leads get followed up on and what counts as a qualified lead in the first place, only works if both sides can actually measure whether it's being met. Too many SLAs get set in a meeting based on a round number that sounds reasonable, then quietly ignored because nobody built the tracking to check it.

Here's a runbook for setting one that's grounded in your real data from the start.

Vendors Covered in this Article

Disclosure: We may earn a commission if you buy through some links on this page. It doesn't change what we recommend.

How do you measure your baseline before setting an SLA target?

Pull your actual time-to-first-contact for marketing-qualified leads over the last quarter, using your attribution or CRM timestamps, before proposing any SLA target. Setting a target without knowing the current baseline usually produces a number that's either trivially easy to hit or wildly unrealistic, neither of which makes for a useful agreement.

Look at the distribution, not just the average. A median that looks reasonable can still hide a long tail of leads that waited far longer than anyone would consider acceptable, and that tail is often where the real relationship friction between the two teams comes from.

What counts as a qualified lead in a sales and marketing SLA?

SLA disputes are rarely about response time itself, they're about disagreement over whether a lead should have counted as qualified in the first place. Write the qualification criteria down explicitly, ideally the same criteria your lead scoring model already uses, so both sides are working from the same definition rather than a vague shared understanding that turns out to differ in practice.

Get sales to sign off on this written definition specifically, not just marketing's summary of it. A definition sales never actually agreed to in writing tends to resurface as a dispute the first time a borderline lead gets debated.

Step three: set the response time target from the baseline, not from a guess

Use your baseline data to set a target that's a genuine improvement but achievable, rather than an arbitrary round number like one hour that nobody has validated is realistic for your team's actual staffing and process. A target set fifteen percent faster than your current median is a more useful starting point than a number chosen because it sounds impressive in a sales kickoff deck. Agreeing on a stretch, but reachable, target this way also makes the eventual review conversation far less adversarial than debating an arbitrary number would.

For example, if your median time to first contact is a few hours but the slowest tenth of leads waited days, a target built on the median alone would hide that tail. Set one target for the typical lead and a separate escalation rule for leads that wait beyond an agreed limit, so a long wait triggers a conversation before it becomes a dispute. Write both numbers into the same document as the qualification criteria, and have both teams sign off. Then review misses together, asking whether staffing, lead volume, or qualification criteria caused them.

Step four: build the measurement before you need it for a dispute

  • Track time-to-first-contact automatically from the timestamp a lead is marked qualified to the timestamp of the first logged sales touch
  • Make the measurement visible to both marketing and sales on a shared dashboard, not something only one side can see
  • Set a review cadence, monthly is reasonable, to look at SLA performance together rather than only when someone raises a complaint
  • Track qualification accuracy too, the share of qualified leads sales considers genuinely qualified, alongside response time, since both sides of the agreement need their own measurement

Step five: use call and contact data to close the loop

Call-tracking and phone tools such as KrispCall or WhatConverts can log call timing and outcome and tie calls and form fills back to the campaign that generated them, which makes SLA measurement more reliable because the first-contact timestamp is captured automatically rather than depending on a rep to log it; confirm each tool's current features first. A manually logged SLA metric tends to drift over time as logging discipline slips, which quietly erodes trust in the whole agreement even when actual performance hasn't changed.

Step six: revisit the SLA as volume and team size change

An SLA set when the team was handling a modest lead volume can become unrealistic once volume grows significantly, or conversely can become too easy once the team grows faster than lead volume does. Treat the SLA as a living agreement tied to current capacity, not a one-time decision, and revisit it whenever either side of the equation, lead volume or sales team size, changes meaningfully.

Executive Capability Standard

What Good Looks Like

The standard is an SLA set from a measured baseline, with a shared, automatically tracked view of performance both sides can see, rather than a target agreed on in a meeting and never actually measured.

Building The Capability (5-Stage Skill Ladder)

1. Learn:Pull your current time-to-first-contact baseline and qualification accuracy before proposing any specific SLA target.
2. Do Manually:Manually track SLA performance against the agreed target for the first few months, using it to validate whether the target was set reasonably.
3. Delegate:Have a RevOps or sales operations hire own the ongoing SLA measurement and monthly review between marketing and sales.
4. Automate:Automate time-to-first-contact tracking from timestamped CRM and call data, so the measurement doesn't depend on manual logging discipline.
5. Buy:Bring in a RevOps consultant if sales and marketing systems aren't currently reconciling cleanly enough to produce one trusted shared measurement.

How to Get Started

Disclosure: We may earn a commission if you buy through some links on this page. It doesn't change what we recommend.

Frequently Asked Questions

What's a reasonable time-to-first-contact target for marketing-qualified leads?

There's no universal number that fits every team, since it depends heavily on staffing, lead volume, and how leads are qualified. Set the target from your own measured baseline rather than adopting a number from a generic best-practice list that wasn't built around your actual capacity.

What should happen when the SLA isn't met?

Treat a missed SLA as a signal to investigate, not automatically as a fault to assign. It could point to a staffing gap, a spike in lead volume, or a qualification criteria that's letting through leads sales doesn't consider ready. Look at the pattern before assuming it's a simple follow-up speed problem.

Should marketing and sales use the same tool to measure the SLA?

Ideally yes, or at least tools that sync into one shared view. Measuring from two separate systems that don't reconcile cleanly is a common source of SLA disputes that have nothing to do with actual performance and everything to do with mismatched tracking.

About the numbers

This guide doesn't quote a sourced benchmark. Figures in it are estimates or general guidance, so check them against your own numbers.

Related Guides